-FREE FREIGHT- Topargee H2F-FM Digital Water Tank Gauge 12V - Flush Mount - Displays Litres Left in Your Water Tank - Nothing Fitted to Your Tank - In Line Flow Meter (H2F-FM)
FREE FREIGHT Topargee H2F Digital Water Tank Gauge - New Larger Display with Backlighting and Auto Off - Recess Mount
*Areas Within Australia - Queensland, Victoria, NT, South Australia, ACT, NSW, Tasmania and Western Australia
Australia's Best Price on Topargee H2F Water Gauge - Flush Mount - Nothing Fitted to Your Tank - In Line Flow Meter
New model now with larger LCD screen and back lighting
This gauge differs from conventional water tank gauges as it actually measures and displays how many usable litres remain in your tank, so you will never be left unsure!
Specifically designed for Marine, Boats, Yachts, Caravans, Camper-trailer, Motorhome and RV
Topargee H2F Water Tank Gauge - Recessed (Flush) Mount - Nothing Fitted to Your Tank - In Line Flow Meter (H2F FM)
Displays number of litres left in your water tank
Take all the Guesswork Out of Your Water Supply
New model now with Larger Screen and Back lighting
Installation is remarkably easy with the sender unit fitted in the hose line, just before or after the pump, nothing is fitted to the tank. This eliminates the problem of having to remove the tank, drill holes, remove filings, seal sender holes, ongoing cleaning/maintenance.
Breakthrough design for the RV and Marine Industries
N.B. Does not include hose connectors, see Connecting Sender Unit below.
Our new RV senders and electronics are compatible with all commonly available RV and marine water pumps and will even work with gravity fed systems.
Fitting recessed display
The LCD Polarised Display on this new model is designed to be only visible when viewed from an angle just below horizontal.
When viewed from this angle the display is extremely clear.
Using the display as a template mark out hole and cut to suit.
Fix in position with bolts provided or suitable screws.
Connecting Sender Unit
Sender unit comes pre-wired with an approximately 1.4m cable. Extra 1.4m extension leads are available for the three pin plugs, up to 6 leads may be joined to make 9.8m in total length. Leads cannot be cut and joined, doing so will void warranty, No Exceptions.
The thread specifications of the sender unit are 1/2" BSP male. Make sure the sender is fitted with the water flow in the direction of the arrow.
You will need to purchase two 1/2" BSP female connectors to the size hose you have, usually 1/2" or 3/4" and two clamps. “John Guest quick connections” also have fittings to suit their hose and the 1/2" BSP sender unit.
Connection to 12 Volt DC
Simply cut off the two pin 12v plug to the required length and connect the black wire to the negative terminal and the red wire to the positive power source.
Programming Monitoring Capacity
Press "DISPLAY" button to turn display on, then press the "PROG" button, "ProG" will blink on the LCD display. Press and release "RESET" button to choose the value of the right digit. Once the value has been chosen, press "PROG" button to save the value, it will then go to the next digit. Repeat the above procedure to program the values for the five digits from right to left.
The maximum monitoring capacity is 99,999 litres. The first time the meter is used fill the water tank and then use normally until empty. Then note how many usable litres the tank holds and reset the meter accordingly.
*If there is no input for one minute during the programming procedure, the programming procedure will be terminated and goes back to the original status.
The TOPARGEE H2Flow will automatically turn on and display the litres remaining when there is water flowing through the sensor e.g. a tap is turned on. It will automatically turn off 10 seconds after there is no water flowing.
To manually check remaining litres, press and release “Display” button and remaining litres will be displayed for 10 sec.
End of Capacity Alert
The TOPARGEE H2Flow will give an audible alert and the digits blink on the LCD display when the remaining capacity reaches zero or minus.
When the water tank has been refilled. Press "DISPLAY" button to turn display on, then press the "RESET" button for five seconds, the "rESEt" on the LCD display blinks twice and the buzzer will sound, the unit will then be reset to the originally programmed value. TIP! You may find it easier to use the side of your fingernail or coin etc. to hold the button in for the five seconds.
Note: Due to continuous product improvement, specifications are subject to change without notice.